1/7ページ
ダウンロード(544.1Kb)
このカタログについて
ドキュメント名 | High Capacity NDT-Filmprocessor Colenta INDX 43/55 |
---|---|
ドキュメント種別 | 製品カタログ |
ファイルサイズ | 544.1Kb |
取り扱い企業 | ポニー工業株式会社 (この企業の取り扱いカタログ一覧) |
この企業の関連カタログ
このカタログの内容
Page1
data sheet
INDX 43/55
High Capacity
NDT - Filmprocessor
Processing capacity : @ 8min Dry to Dry : 54cm/min (21 in/min)
COLENTA NDT Film Processors type:
INDX 43/55 07/2013 TK
to be used to process all standard NDT Films.
page 1 / 7
Page2
INDX 43 / 55
NDT - Filmprocessor
Technical Specifications
Processing applications: Rolls/Cut sheets of industrial x-ray films
Film thickness: 0,10mm (4mil) - 0,18mm (7mil)
Material width: min. 7,5 cm max. 43cm
Material length: min. 10 cm
Time in Cycle Time Intake
Capacities Developer (dry to dry) speed
for: [sec] [min] [cm/min]
INDX 43/55 50 3.37 109
250 16,87 21
additional, see the table on following page.
INDX 43/55
Tank capacity - Developer: 20 L (incl Filter)
Fixer: 23 L (incl Filter) Microprocessor
Wash water: 20 L controlled Display
Solution heating (DEV and FIX): adjustable in a range of 18°C - 43°C via Microcontroller
(separate inline 800W heaters)
Wash Water heating: adjustable in a range of 18°C - 43°C via thermostat
(separate inline 800W heaters)
Dryer: warm air - adjustable in a range of 18°C - 55°C
Replenishment: fully automatic - replenishment is microprocessor controlled and
calculated from information received from sensors measuring the
width and length of material entering the processor.
Replenishment cycles are adjustable.
Water supply: 2 magnet valves:
- 1 x 2way valve (warm or cold water supply) for Wash
- 1 x single valve (cold water) for cooling
required water pressure: 3 - 10 bar external filter for
Wash water supply: filtered at a temperature of 8°C - 12°C DEV and FIX
with 3/4" hose connection
Wash water drain: 32mm (5/4inch) hose or tube
INDX 43/55
Weight: Empty 290 kg
with solution 353 kg
with packing 406 kg
Technical specification subject
to change without notice.
page 2 / 7
Page3
Transport System
INDX 43/55
Anti run-back system
with fixer.
DEV FIX WASH
(Main-Wash)
DRY
page 3 / 7
Media in
Pre-Wash
Page4
Production Graph
INDX 43/55
page 4 / 7
Page5
Production Graph
INDX 43/55
Automatic Cooling: The processor electronics will automatically detect over temperature
developer / fixer conditions and then activate a cold water cooling system. The temperature of
the incoming cold water supply should be between 8 - 12 C in
order for the system to operate efficiently. If not available and in
cases where the processor is required to operate in warm ambient
conditions a chiller system should be used on the developer tank
solution. A chiller unit is available as an optional accessory from
Colenta for either self installation or factory fitted if ordered with the
processor.
other optional accessories:
external chiller unit
rack carrier drip tray level control for replenisher tanks
silver recovery unit
page 5 / 7
Page6
Dimensions:
INDX 43/55
Ventilation port
# All dimensoins are in mm.
# We recommend to keep a minimum walking space of 600mm
around the processor.
Processor ventilation: The 43/55 is supplied with an exhaust port located at the feed end of the
processor. During installation this port must be connected to an external ventilation system provided
at the installation site (sufficient power to ventilate the warm exhaust air away and out of the processing
area).
Where the processor is installed in a „through wall“ location whereby an auto feeder or feed table is
positioned in a darkroom and the main body of the processor is in daylight, it is important that the
darkroom is pressurised to ensure a positive airflow from feed to dryer thus avoiding condensation
related problems.
page 6 / 7
Page7
Electrical supply:
INDX 43/55
1) 230VAC+N 50/60Hz
total power consumption 6,9 kW L1
400V~
L2 400V~
1) 230VAC+N 50/60Hz 400V~
fuse to be used 32A L3 230V~
N
2) 3x220VAC 50/60Hz PE
fues to be used 25A Attention:Line voltage 400V in respect to other lines.
Line voltage 230V in respect to neutral.
Only L1-N = 1 x 230V is connected
3) 400/230VAC+N 50/60Hz In case the above voltages are not
fuse to be used 20A available at site, please contact your localdealer or the factory for rewiring advice.
2) 3x220VAC 50/60Hz 3) 400/230VAC+N 50/60Hz
L1 L1
220V~ 400V~
L2 220V~ L2 400V~
220V~ 400V~
L3 L3
110V~ 230V~
N N
PE PE
Attention: Attention:
Line voltage 220V in respect to other lines. Line voltage 400V in respect to other lines.
Line voltage 110V in respect to neutral. Line voltage 230V in respect to neutral.
Neutral is not used
In case the above voltages are not In case the above voltages are not
available at site, please contact your local available at site, please contact your local
dealer or the factory for rewiring advice. dealer or the factory for rewiring advice.
details for shipment:
INDX 43/55
packing dimensions: 1 wodden box on palette
132cm x 101cm x 139cm (L x W x H)
weight with packing: 280 kg
packing dimensions: 1 wodden box on palette
81cm x 65cm x 145cm (L x W x H)
weight with packing: 126 kg
page 7 / 7